Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
new error after update
22-08-2017, 10:03 AM,
#1
new error after update
Hi Jordi.

 I have this error message after update. I´ve seen it in WXP32 and W7 64 bits.

 Can you help me?


Attached Files Thumbnail(s)
   
Reply
22-08-2017, 01:38 PM,
#2
RE: new error after update
I have a Kenwood TS-480Sat and I´ve seen that tuning from DX messages send me a report with the frecuency before send to my TXCVR. Ej: 14023.8 make a window with 00014023800 and I must hit OK to send to my Kenwood
Reply
22-08-2017, 01:47 PM,
#3
RE: new error after update
returning to old version frecuency change is OK
Reply
23-08-2017, 10:32 AM,
#4
RE: new error after update
Hi,

I'm not at home now, I think I left a test point in the code of the patch that I have to delete! I will change it inmediately later and I will let you know.

Thank you for the error report!


Best 73
Jordi, EA3GCV
Current developer of Swisslog
Reply
23-08-2017, 01:34 PM,
#5
RE: new error after update
(23-08-2017, 10:32 AM)EA3GCV Wrote: Hi,

I'm not at home now,  I think I left a test point in the code of the patch that I have to delete!  I will change it inmediately later and I will let you know.

Thank you for the error report!


Best 73

OK, TNX Jordi. Enjoy your holidays...
Reply
23-08-2017, 08:13 PM,
#6
RE: new error after update
Hi,

I have uploaded a new patch correcting this issue on Kenwood transceivers. Download and replace the EXE in the Swisslog folder:

http://www.swisslogforwindows.com/Beta/Swisslv5.exe

Regarding your LoTW problem, I don't know why but if you see the LotW report, the TQ8 full path doesn't contain any slashes! It's shown as C:SWISSLOGLOTW when it should be C:\SWISSLOG\LOTW\. I don't really know what may happen because it works perfect here and to other users. If you still have this problem contact me directly to my e-mail address or phone to arrange a Teamviewer session.

Best 73
Jordi, EA3GCV
Current developer of Swisslog
Reply
24-08-2017, 06:45 AM,
#7
RE: new error after update
(23-08-2017, 08:13 PM)EA3GCV Wrote: Hi,

I have uploaded a new patch correcting this issue on Kenwood transceivers. Download and replace the EXE in the Swisslog folder:

http://www.swisslogforwindows.com/Beta/Swisslv5.exe

Regarding your LoTW problem, I don't know why but if you see the LotW report, the TQ8 full path doesn't contain any slashes! It's shown as C:SWISSLOGLOTW when it should be C:\SWISSLOG\LOTW\. I don't really know what may happen because it works perfect here and to other users. If you still have this problem contact me directly to my e-mail address or phone to arrange a Teamviewer session.

Best 73

 Hi Jordi, all problems are now OK with this version. I don´t know why the bad path. NOW OK WITH THIS VERSION.

 Great job sir. 73
Reply
24-08-2017, 11:01 PM,
#8
RE: new error after update
Perfect!!
Jordi, EA3GCV
Current developer of Swisslog
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)